Choosing A Top Coat For Your Woodworking Project
Jonti-Craft Childs Rocker Wood Rocking Chair 0578JC
When you're done with your woodworking project, of course you want to protect it. A top coat protects the finish of your project, as well as the wood itself. If you leave the wood (and any stain or paint you've used) as it is, it's likely to get scratched or dirty, and will also get damaged by watermarks if it comes into contact with moisture. By using a good wood finish, you'll keep your wood and its finish clean and protected, and prevent it from damage, wear and tear. You can apply a clear finish so as to accentuate the grain, or even give it a "wet look" if you like. In general, unfinished wood will develop a dull matte texture that will not show off the grain.
No matter the woodworking project you're working on, there are two basic finishes you can apply. The first is called an "evaporated finish." With this type of finish, it "cures" and becomes hard simply by drying. These types of finishes include lacquers and water-based finishes. You can soften these finishes with heat; therefore, they are given the name "thermoplastic."
The second type of wood finish is called a "reactive finish." This is cured by allowing it to react with another component, such as air, or with another chemical added just prior to the finish's application. Some examples of these include oils in oil-based varnishes or catalyzed lacquers. These types of finishes are called "thermosetting finishes." Unlike the thermoplastic finishes, these finishes are not softened with heat or with the original solvent used.
Within the reactive finishes are two different types of oil finishes. These are oils that dry when exposed to air or oils that do not dry when exposed to air. In example of an oil that does not dry when exposed to air is mineral oil, or baby oil. Those that do dry protect would better than those that don't dry. Therefore, usually, the ones that do dry should be used to finish your wood project.
Most often, linseed or tung oil is used to finish wood. These are distinguished from other types of wood products because they are "true" oils. Both penetrate the finish, which means that they enter the wood fibers themselves. Then they harden within the wood, which makes them the easiest to apply. Simply wipe down wood with them to allow them to penetrate the wood for a few minutes, and then wipe off the excess with a clean rag. If you apply several coats, you will not build up a hard film like you might with a varnish or lacquer, because the film itself dries to a very soft and smooth sheen.
Linseed oil is made from the flax plant. The oil itself is pressed from the plant. It is available both in on refined (also called "raw") form or in refined form. Unrefined linseed oil dries quite slowly and is usually not used on wood. By contrast, boiled linseed oil is thicker and dries more quickly. Usually, the boiled linseed oils available today also have chemical additives to speed up the drying time, which makes them much more suitable for finishing wood.
Megan Cherry writes for http://www.pegandrail.com If you are looking for a high quality well made coat rack step in and check us out, we manufacture a complete line of wall mounted coat rack from a shaker peg style coat rack to a modern wall coat rack with brass hooks or satin nickel for the brushed stainless steel look we even have a very modern looking hand rub white lacquer coat racks to go along with our line of Oak, cherry and Maple wall coat racks, we can even manufacture you a custom size coat rack or even ship you a coat rack that is unfinished.
Related Articles:
A Diy Guide On Woodworking Jigs
Woodworking jigs are a necessary part of any woodworking shop. They are great for repetitive tasks in many wood working projects. They make complex projects easier to manage and faster. You can purchase pre made jigs or make your own. Although they are inexpensive, making your own from scrap wood is even cheaper. Depending on the type of projects you like to do, you will need a variety of different jigs. Types of Woodworking Jigs Dovetail jigs are great for making dovetail joints accurately. These can be purchased relatively inexpensively. Another option is to make your own dovetail jig. You can find templates for making your own jigs on the internet or in most stores that sell wood working supplies. Many of these templates allow you to...
Woodworking: The Best Wood For Beginners
Woodworking: Know Your WoodWood is made of cellulose fibers, held together with a property called lignin, and is classified as hardwood or softwood, depending on the type of tree from which it comes. In addition, sapwood or new growth wood on a tree is still alive, while heartwood refers to the part of the tree that is no longer functioning.
Woodcraft Launches Woodworking Tip Site at LifeTips.com
Woodcraft is now the exclusive woodworking sponsor in the LifeTips network.
Choosing The Proper Finish For Your Woodworking Project
If you've finished your woodworking project, congratulations. Now, what type of finish do you want to put on it so that not only will you protect your hard work for years to come, but also enhance its innate beauty? No matter what you choose, you have to choose the right finish so that your hard work will be as beautiful finished as it was unfinished. Choosing the wrong finish can make your project look less beautiful than it should.
Contribution Of The Woodworking Show On Consumers
Home improvement and woodworking shows may cause more harm than good for some homeowners. Some Canadians, for example, are choosing their dream renovations rather than remodeling within their budget and financial reality. A recent survey showed that sixty percent of respondents who recently took on a home renovation actually developed a budget prior to beginning. However, twenty-seven percent spent more than budgeted. Sticking to a home improvement budget is, definitely, a challenge especially when television shows and magazines influence the desire for the latest appliances and trendy d?cor. Though the intention is good and many home renovators want to stay within their budget, it is often difficult which can cause major headaches once th...
Woodworking Tools: Right Selection And Care Will Save You Money, Part 6
Woodworking: Tools Of The Trade, Part 6 - Finishing EquipmentA civilization's maturity and intelligence is judged, in part, by the diversity and sophistication of its tools. When it comes to woodworking, the human race is quite advanced.
The Most Important Step For Your Woodworking Project
A hugely important aspect of any woodworking project is the plans that explain to you what you?re to do. Having good woodworking plans can mean the difference between a successful or dreadful ending to your project.
Woodworking Supplies
Easier ?The Woodworking is on kind of art or else craft of making all the different things of wood. The craftsman also uses the woodworking tools in order to shape the wood.
Construction Tools. Wood Router.
A router is a working tool of the wood used with the rout outside (cavity outside) a sector vis-a-vis a piece of wood. It was a tool used in particular by manufacturers of model and manufacturers of staircase and was composed of a plane out of wooden offering all the range of products of hand with a narrow blade projecting well beyond its base plate gaining it the tooth woman of nickname of the old woman. Since approximately 1960, it was replaced by the modern router of axis, which was designed for same work, although the first electric routers of hand appeared in years just before the First World War.
ToolKing.com Partners with Popular Woodworking Magazine's "Best New Tool" Winner- Steel City Tool Works
ToolKing.com announced today a partnership with Steel City Tool Works. Steel City Tool Works has been recognized as Popular Woodworking Magazine as "Best New Tool" for its entire line of products.
Woodworking Tools
Most people think "power tools" when they think of woodworking, but hand tools are also important for woodworking. If you are just starting out in woodworking, you want to make sure you get the right tools, and not spend a lot on unnecessary items.
Knowing The Woodworking ?Terminology?
Woodworking is responsible for lots of the houses, furniture and other wooden materials and articles used in homes and office surroundings. Simply defined, woodworking is the art or craft (of which it seems more like magic) of creating things out of wood. Woodworking is usually done by a carpenter but nowadays anyone can do it, it can be learned to a point in a very short period of time and is a very enjoyable pass time.
Construction Tools. Wood Router. The Features.
The tool is usually composed of a low housing a universal electric motor vertically assembled with a ring on the end of its axis. The little is size-adjustable to allow the projection by an opening in ladies punts, usually via adjusting the size of engine-support (the mechanism of the adjustment is changed considerably among manufacturers). The ordering of the router is derived from a handle or a button on each side from the device, or by the ?closed handle? recently more developed. There are two standard of dive of router and fixed types.
Woodworking Tools: Right Selection And Care Will Save You Money, Part 1
Woodworking: Tools Of The Trade, Part 1 - A Place To WorkA civilization's maturity and intelligence is judged, in part, by the diversity and sophistication of its tools. When it comes to woodworking, the human race is quite advanced.
Purchasing Woodworking Tools
A variety of woodworking machinery and tools is needed for both home and professional workshops. Several companies make quality woodworking machinery, including Craftsman, Rockwell, Rigid and Milwaukee.